edwina@edwin-pump.com
View All Products
en
Reliable water pressure is essential in homes, commercial buildings, agricultural facilities, industrial plants, HVAC installations, and water treatment systems. As demand for efficient and intelligent water equipment increases, pump users are looking for more than basic fluid transfer. They need stable pressure, low energy consumption, quiet and dependable operation, simple controls, protection against common operating risks, and long service life. The XLA403 Intelligent Permanent Magnet Multistage Pump is designed to address these requirements in one compact pumping solution.
The XLA403 combines a multistage centrifugal hydraulic design with an intelligent permanent magnet motor and automatic operating functions. It is suitable for clean water and other low-viscosity, neutral, non-explosive liquids that do not contain fibers or harmful solid particles. With a maximum flow of 66 liters per minute, a maximum head of 25 meters, and a maximum suction lift of 5 meters, the pump is appropriate for domestic pressure boosting, water circulation, light commercial applications, hot and cold water movement, and selected industrial duties.
Its design reflects a clear shift away from conventional fixed-speed pumps. Traditional pumps often run at a constant output whether the system requires full capacity or only a small amount of water. This can result in unnecessary electricity consumption, unstable pressure, excess heat, and greater mechanical stress. The XLA403 instead uses intelligent control and a high-efficiency permanent magnet motor to adjust power output according to operating demand. The result is a more responsive, economical, and flexible pumping system.
XLA 403 Intelligent Permanent Centrifugal Pump Magnet Multistage
The XLA403 is not simply a standard centrifugal pump with an electronic control panel. It is a compact intelligent booster system engineered around the interaction of the motor, hydraulic stages, sensors, control logic, and protective functions. Each part contributes to overall operating efficiency and reliability.
The permanent magnet motor is the foundation of its energy-saving performance. The motor is rated at IE5 high-efficiency performance and can achieve efficiency of up to 96 percent under appropriate operating conditions. Compared with many conventional asynchronous motors, the permanent magnet motor can reduce electrical losses and provide more efficient conversion of electrical energy into hydraulic output. The supplied product information indicates that the motor can deliver more than 30 percent energy savings compared with asynchronous motor solutions, depending on the working condition and system demand.
The pump also provides variable power operation from 100 to 400 watts. This range enables the unit to respond to different water requirements instead of continuously consuming the maximum rated input. When the demand is lower, the intelligent control system can reduce the motor output. When a higher pressure or flow requirement is detected, it can increase performance within the pump’s operating limits.
The multistage hydraulic configuration is another major advantage. A multistage pump develops pressure through several impeller stages rather than relying on one large impeller operating under extreme conditions. This arrangement allows the pump to generate useful head from a compact body while maintaining a balanced flow path. It is especially suitable for building water boosting, hot water circulation, water tower systems, and other applications in which stable pressure is more important than very high volume.
The pump is also designed for practical installation. Its 1-inch inlet and outlet connections make it compatible with many commonly used household and light commercial pipe systems. Its compact dimensions of 301 by 146 by 228 millimeters support installation where space is limited. With a net weight of approximately 4.5 kilograms, it can be handled more easily than many larger conventional booster systems.
One of the most useful features of the XLA403 is its one-click pressure regulation function. Users do not need to operate a complicated control sequence to make a basic pressure adjustment. The intuitive interface is designed to simplify commissioning and everyday use, making the pump accessible for residential users as well as technicians working on commercial installations.
Pressure adjustment is important because every water system has different requirements. A small household with one bathroom may need a different pressure setting from a multi-floor residence, a garden irrigation system, or an industrial cleaning line. A pump that cannot adapt may either underperform or consume more energy than necessary. The XLA403 provides a more practical approach by allowing the operating pressure to be adjusted according to the application.
The intelligent controller also supports automatic response to changing demand. When several outlets are opened at the same time, the system can respond to the increased requirement. When water use decreases, the pump can reduce output rather than continuing to run at maximum capacity. This approach improves comfort for users and helps reduce operating costs over the lifetime of the equipment.
Automatic control also minimizes the need for constant manual supervision. Once the pump has been correctly installed and configured, it can operate as part of an automated water supply or circulation system. This is particularly useful for buildings, agricultural facilities, and industrial installations where water demand changes throughout the day.
For professionals comparing intelligent booster pumps, the control system is as important as the motor rating. A high-performance motor alone does not guarantee efficient operation if it is operated without appropriate load management. The XLA403 combines motor efficiency with intelligent output control, giving it a practical advantage over fixed-speed pumps that lack demand-based regulation.
Motor efficiency affects both direct energy costs and the long-term operating condition of a pump. In a conventional motor, part of the electrical input is lost as heat through resistance, magnetic losses, and other forms of inefficiency. The permanent magnet design used in the XLA403 reduces some of these losses by using permanent magnetic fields rather than relying entirely on electrically generated magnetism.
The stated IE5 efficiency level places the motor in a high-efficiency class. Under suitable operating conditions, efficiency can reach up to 96 percent. This means that a larger proportion of the electrical input is converted into useful mechanical power. Lower losses also mean reduced heat generation inside the motor, which can support improved thermal stability and service life.
The pump uses 100 percent copper winding wire. Copper has excellent electrical conductivity and is widely used in quality motor construction because it helps reduce electrical resistance. The use of pure copper winding supports stable current transmission and contributes to lower heat generation compared with less conductive winding materials. It also helps maintain reliable performance during repeated starts, extended operation, and changing loads.
Motor winding quality is especially important in booster applications. A booster pump may start and stop frequently as users open and close taps, appliances operate, or automatic controls respond to pressure changes. Inferior winding materials can increase heat accumulation and reduce motor durability under such conditions. The XLA403’s copper winding construction is intended to provide a stronger foundation for dependable operation.
The motor can operate with 50 or 60 hertz frequency, giving the product broader compatibility for international markets. Its wide-voltage and dual-frequency support can simplify product selection for distributors, contractors, and users working in regions with different electrical standards. Electrical compatibility must still be confirmed before installation, but the broad frequency design improves application flexibility.
The hydraulic system is designed to provide a maximum head of 25 meters. Pump head represents the energy the pump can add to the water and is commonly used to evaluate whether the unit can overcome elevation, pipe resistance, fittings, and required outlet pressure. A maximum head of 25 meters makes the XLA403 suitable for many small buildings, domestic water systems, water tower arrangements, and light commercial pressure applications.
With a maximum flow of 66 liters per minute, the pump offers a useful balance between pressure and volume. The actual flow available in an installed system will depend on pipe length, elevation, fittings, water temperature, pressure setting, and other resistance factors. Nevertheless, the rated capacity indicates that the pump is intended for more than a single low-demand outlet. It can support multiple applications when correctly sized and installed.
Multistage construction distributes the pressure-generating work across multiple hydraulic stages. This can improve the balance between compact dimensions and pressure capability. Instead of using a large single-stage arrangement, the pump creates pressure progressively, allowing the hydraulic assembly to remain relatively compact.
The maximum rotational speed is listed as 4,800 revolutions per minute. High-speed operation allows the pump to achieve strong performance from a relatively small motor and housing. Because higher speed also makes hydraulic balance, sealing, material selection, and control accuracy important, the complete assembly must be manufactured and tested carefully. The XLA403 addresses these requirements through its integrated design, engineering plastic hydraulic components, stainless steel sealing-related components, and intelligent operating controls.
Users should select the pump according to the actual system curve rather than relying only on maximum values. Maximum flow and maximum head are normally achieved at different points. A professional installation should evaluate the expected flow, static lift, pipe resistance, pressure requirement, and water temperature before final selection.
Material selection influences pump life, hydraulic efficiency, maintenance requirements, and compatibility with the pumped liquid. The XLA403 uses engineering plastic for the pump body, base, upper cover, and impeller. Engineering plastics can provide several practical advantages in compact pump construction, including low weight, corrosion resistance in suitable water applications, dimensional consistency, and efficient mass production.
A lightweight engineering plastic pump body is easier to transport and install than a comparable heavy metal housing. This can reduce handling effort during residential installation and simplify positioning in confined equipment rooms. The material also does not rust in the same way as ordinary steel when exposed to clean water, which can support a cleaner and more durable external structure in appropriate environments.
The impeller is also made from engineering plastic. A precisely formed plastic impeller can provide a smooth hydraulic surface and consistent geometry. Its relatively low mass reduces the rotating inertia that the motor must accelerate during start-up. This is helpful in systems where the pump starts periodically in response to pressure demand.
The shaft seal is listed as stainless steel, while the shaft material is specified as silicon carbide and graphite. These components are important because the shaft seal prevents water from entering the motor or other protected areas. Silicon carbide and graphite are widely used in mechanical sealing and wear-related applications because they can provide suitable friction and wear characteristics when correctly matched and lubricated by the pumped medium.
Material suitability depends on the liquid and operating conditions. The XLA403 is intended primarily for clean water and compatible low-viscosity liquids. It should not be used for liquids containing abrasive particles, fibers, aggressive chemicals, or explosive substances unless an appropriate specialized model has been selected. Correct material matching is essential for safe and reliable operation.
Water hammer occurs when the movement of water in a pipe changes rapidly, such as when a valve closes suddenly or a pump stops abruptly. The resulting pressure wave can cause vibration, noise, pipe stress, leakage, and premature damage to fittings. In severe cases, repeated water hammer can shorten the service life of a complete water distribution system.
The XLA403 incorporates a non-return water structure and high-quality sensors to help reduce water hammer effects. The non-return structure helps prevent reverse flow when the pump stops. The sensors and control system support more controlled operation, reducing the likelihood of abrupt pressure changes during common operating cycles.
This feature is valuable in water tower systems, hot water circulation, and whole-house pressure boosting. These installations may contain long pipe runs, multiple outlets, storage tanks, or repeated start-and-stop cycles. By supporting smoother flow transitions, the pump can improve system comfort and reduce stress on connected components.
Water hammer protection does not eliminate the need for correct system design. Proper pipe sizing, suitable valves, appropriate accumulators where required, and correct pump programming remain important. However, the integrated non-return and sensing functions give the XLA403 an advantage over basic pumps that provide no dedicated response to reverse flow or rapid pressure changes.
Equipment that remains unused for a long period can experience mechanical problems. Seals may become less flexible, deposits may form, and rotating parts can become difficult to move. In some conditions, a pump may seize after extended inactivity, especially when it is installed in seasonal housing, backup water systems, or occasional-use facilities.
The XLA403 includes a self-start protection function. When the pump has not operated for a long period, the system automatically activates every 12 hours. This periodic operation helps keep the internal rotating components from remaining stationary indefinitely and reduces the risk associated with prolonged inactivity.
This function is useful in holiday homes, emergency water systems, irrigation installations, and commercial buildings with variable occupancy. It can also provide additional operational confidence where the pump is expected to remain ready for use but is not required to run continuously.
Self-start protection is an example of how intelligent functions can improve equipment availability without requiring users to remember manual maintenance cycles. The feature does not replace regular inspection, cleaning, and professional service, but it adds a useful layer of automatic care to the pump’s operating logic.
The XLA403 has an IP54 protection rating. This level of enclosure protection is designed to help protect the internal electrical components against limited dust ingress and water splashes from different directions. It supports safe use in suitable outdoor or semi-outdoor environments when the pump is installed according to the manufacturer’s instructions.
IP54 does not mean that the pump is waterproof or suitable for immersion. The unit should be protected from flooding, direct high-pressure water jets, standing water, and conditions outside the specified environmental range. Proper electrical grounding, cable protection, ventilation, and drainage are still necessary.
The stated ambient temperature range is 0°C to 40°C, while the liquid temperature range is above 0°C and up to 100°C. This allows the pump to support selected hot and cold water applications, including hot water circulation, provided that the entire installation is suitable for the temperature. Users should consider pipe materials, seals, connections, pressure conditions, and scalding risks when pumping hot water.
The specified relative humidity limit is a maximum of 85 percent. Installations in damp environments should include suitable protection against condensation and prolonged exposure to moisture. Observing these environmental limits helps preserve the motor, control electronics, sensors, and electrical connections.
Taizhou Edwin Electric Co., Ltd., operating under the Edwin Pump brand, was founded in 2008. The company is described as an integrated manufacturing enterprise with capabilities covering independent research and development, mass production, and global export. This integrated structure is important for a product such as the XLA403 because intelligent pump performance depends on coordination between hydraulic design, motor production, electronics, assembly, and testing.
An integrated manufacturer can maintain closer control over the relationship between product design and production. Instead of treating the motor, pump body, impeller, control system, and final assembly as unrelated elements, the manufacturer can develop them as part of a complete system. This supports consistency between prototype development, production tooling, assembly procedures, and finished-product inspection.
Independent research and development also allows the company to adapt products to changing market requirements. The development of solar water pumps and intelligent booster pumps since 2018 demonstrates an investment in new energy and intelligent technology. The XLA403 reflects this direction by combining efficient permanent magnet drive technology with automatic pressure control and protection features.
Mass production capability is valuable to distributors and project purchasers because it supports repeat orders and product availability. Consistent manufacturing processes can help maintain uniform dimensions, electrical performance, hydraulic characteristics, and component fit across production batches. This is especially important for contractors who install multiple pumps in similar buildings or for distributors who need dependable replacement supply.
The company’s product portfolio includes deep well pumps, submersible pumps, domestic booster pumps, circulation pumps, solar water pumps, and other water equipment. This broad experience provides a practical understanding of different pumping environments, including agricultural irrigation, municipal engineering, construction, HVAC systems, household water supply, mining, and new energy projects.
The company also established Taizhou Haipai Import & Export Co., Ltd. and Golden Falcon Industrial Co., Ltd. to support procurement planning, order tracking, cross-border delivery, and foreign trade services. For international buyers, this additional service structure can simplify communication, purchasing coordination, shipping preparation, and project follow-up.
The quality of an intelligent pump depends on more than the specifications printed on a product label. Manufacturing accuracy affects hydraulic balance, motor efficiency, sealing performance, noise, vibration, and operating life. The XLA403’s construction indicates several important production priorities.
The pump body, base, upper cover, and impeller are produced from engineering plastic. This type of construction requires controlled forming conditions to maintain dimensional stability and repeatable geometry. The internal hydraulic passages must be consistent so that water flows smoothly through the stages. The impeller must also maintain accurate balance at its operating speed.
Consistent component dimensions support easier assembly and reduce the risk of leakage or misalignment. For mass production, repeatable tooling and process control are particularly important because small variations in hydraulic components can affect the performance of the finished pump.
The use of 100 percent copper wire requires proper winding, insulation, connection, and testing processes. Correct winding tension and placement help maintain electromagnetic balance and reduce the possibility of localized heating. Secure electrical connections are also important for stable operation under varying loads.
Because the XLA403 includes intelligent electronic control, the motor and controller must operate as a coordinated system. Electrical assembly should therefore include checks for insulation, wiring integrity, sensor connection, control response, and protection functions. A high-efficiency motor delivers its full benefit only when the electrical and control systems are correctly matched.
The shaft, shaft seal, and rotating assembly must be installed with suitable alignment. Poor alignment can increase friction, vibration, and wear. Correct seal installation is especially important because the seal protects the motor and electrical areas from the pumped liquid.
The specified stainless steel shaft seal and silicon carbide/graphite shaft materials are selected for a demanding part of the pump. Production control should ensure that contact surfaces are clean, components are correctly positioned, and the rotating assembly moves freely before final closure.
Final assembly brings the hydraulic, motor, electronic, and protective systems together. The completed pump should be checked for correct rotation, electrical response, pressure behavior, flow performance, leakage, abnormal noise, vibration, and control operation. For an intelligent booster pump, testing should also include pressure adjustment and automatic response to changing demand.
Integrated manufacturing supports this type of coordinated verification. When the manufacturer has responsibility for product development, component production, assembly, and export preparation, it can establish a more unified quality approach than a fragmented supply chain with limited control over the final product.
The XLA403 is suitable for a broad range of clean-water applications. In residential buildings, it can support whole-house pressure boosting where municipal pressure is insufficient or upper floors require stronger water delivery. It can also be applied to water tower systems, hot water circulation, and household distribution networks.
In commercial buildings, the pump can serve small offices, guest houses, restaurants, retail units, and service facilities. Stable pressure can improve the operation of washrooms, kitchen equipment, cleaning stations, and other water outlets. The compact form factor makes it useful where a large pump room is not available.
For HVAC and cooling systems, the pump can support circulation of compatible water within the specified temperature and environmental limits. Its intelligent output control may help reduce energy consumption when the system load changes during the day or across different seasons.
In industrial settings, the XLA403 can be used for water transportation, circulation, industrial cleaning systems, water treatment support, and liquid transfer. It may also be suitable for selected food, beverage, agricultural, and ingredient systems when the liquid is compatible with the pump materials and the installation meets all applicable hygiene and safety requirements.
The pump is also suitable for water purification support systems. It can assist in moving clean water through treatment equipment, storage arrangements, and distribution lines. However, the specific liquid quality, chemical composition, filtration level, and system pressure must be evaluated before use.
| Application area | Typical purpose | Important selection consideration |
| Residential water supply | Whole-house pressure boosting and upper-floor supply | Required pressure, simultaneous outlets, pipe resistance |
| Water tower systems | Controlled transfer and pressure improvement | Tank elevation, non-return protection, start-stop frequency |
| Hot water circulation | Movement of compatible hot water | Liquid temperature, seal compatibility, thermal safety |
| HVAC and cooling | Water circulation through system loops | System resistance, operating temperature, control strategy |
| Industrial cleaning | Clean-water supply for washing processes | Water quality, required flow, duty cycle |
| Water treatment | Transfer of treated or filtered water | Liquid composition, filtration, pressure requirement |
| Agricultural and ingredient systems | Low-viscosity liquid circulation and transfer | Compatibility, hygiene requirements, operating environment |
The XLA403 is intended for clean water and compatible liquids with low viscosity. The supplied specifications allow solid particles below 0.1 percent by volume, with particle size below 0.2 millimeters. In practical terms, the pump should be protected from sand, gravel, fibers, sludge, and other abrasive or obstructive materials.
Solid particles can damage the impeller, increase wear at the shaft seal, block narrow internal passages, and reduce hydraulic efficiency. A suitable filter or strainer may be required where the water source contains suspended material. The filter should be selected so that it protects the pump without creating excessive suction resistance.
The specified pH range is 4 to 10. Liquids outside this range may attack engineering plastic, metal, sealing surfaces, or other internal parts. Even liquids within the pH range may contain chemicals that are incompatible with the pump materials. The term clean water should therefore be interpreted carefully, especially in industrial applications.
The pump is not intended for explosive liquids or liquids containing fibers. Oil or oil-based liquids require a special pump type, according to the supplied product information. Users should never assume that a water pump can safely handle fuel, solvents, concentrated chemicals, or flammable liquids.
Before commissioning, the installer should confirm liquid temperature, viscosity, chemical composition, particle concentration, pressure, and expected operating hours. Correct application matching is one of the most effective ways to obtain long service life.
The XLA403 offers several advantages compared with conventional fixed-speed booster pumps. The first is energy efficiency. A traditional motor may continue to run at a relatively constant speed even when the system needs only a small amount of water. The XLA403 can adjust its output according to demand, helping avoid unnecessary energy use.
The second advantage is more stable pressure control. Fixed-speed pumps often cause pressure fluctuations because they start at full output and stop when a pressure threshold is reached. Intelligent regulation can provide a smoother response, improving user comfort and reducing stress on pipes and valves.
The third advantage is compact performance. The multistage design provides up to 25 meters of head from a pump measuring only 301 by 146 by 228 millimeters. This can be a significant benefit in homes, apartments, equipment cabinets, and compact plant rooms.
The fourth advantage is integrated protection. The XLA403 includes water hammer reduction, self-start protection, IP54 enclosure protection, and multiple built-in safety functions. A basic pump may require additional external devices to achieve a comparable level of operational support.
The fifth advantage is application flexibility. Dual-frequency operation, wide-voltage support, one-click pressure adjustment, and compatibility with hot and cold water systems make the pump useful across different markets and installation conditions.
Finally, the permanent magnet motor and copper winding construction provide a stronger efficiency and durability proposition than low-cost pumps using less efficient motors and lower-grade winding materials. The complete value should be evaluated not only by initial purchase price but also by electricity consumption, maintenance requirements, operating comfort, and replacement frequency.
A successful installation begins with correct pump selection. The expected flow and pressure should be calculated from actual water demand, elevation, pipe length, fittings, and outlet requirements. Maximum flow and maximum head should not be treated as simultaneous operating values.
The pump should be installed on a stable, level base that can support its weight and limit vibration. Pipework should be properly supported so that the pump connections are not exposed to excessive mechanical stress. The inlet pipe should be as short and direct as practical, with attention to avoiding air leaks and unnecessary restrictions.
Before starting the pump, the system should be filled and air should be removed according to the installation procedure. Dry running can damage seals and hydraulic components. Any strainer or filter should be clean, and all connections should be checked for leakage.
The electrical supply must match the applicable pump requirements. Wiring should be carried out by qualified personnel, with suitable grounding and protection. The IP54 rating does not remove the need for proper electrical installation or protection from flooding and direct water jets.
After installation, the pressure should be adjusted using the one-click control function. The installer should observe start-up behavior, outlet pressure, flow stability, noise, vibration, and any error indications. The system should be tested under low and high demand to confirm that the intelligent controller responds correctly.
For hot water applications, the installer must consider thermal expansion, insulation, burn prevention, and the compatibility of connected components. The maximum liquid temperature is 100°C, but the complete system must be designed for the selected operating temperature.
Although the XLA403 is designed for reliable automatic operation, regular maintenance remains important. The pump exterior should be kept clean, ventilation areas should remain unobstructed, and electrical connections should be inspected periodically. Any unusual noise, vibration, leakage, pressure loss, or repeated error condition should be investigated promptly.
Filters and strainers should be inspected and cleaned according to water quality and operating frequency. A blocked filter can reduce inlet pressure and cause poor pump performance. It may also increase motor load and create unfavorable suction conditions.
Users should monitor the pump for changes in operating behavior. A gradual reduction in pressure may indicate a clogged filter, air entering the suction line, worn hydraulic components, or a change in the water source. Increased noise may suggest bearing, seal, cavitation, or alignment problems.
The automatic self-start function helps reduce the risks associated with inactivity, but seasonal installations should still be inspected before being placed back into full service. Pipes should be checked for freezing, leakage, deposits, and damage. In cold climates, the pump and connected pipework must be protected against temperatures below the specified operating range.
When maintenance is required, electrical power should be disconnected and the system pressure should be safely released. Repairs involving the motor, control electronics, shaft seal, or internal hydraulic components should be completed by trained personnel using appropriate replacement parts.
For distributors, contractors, and original equipment buyers, product support is an important part of pump value. Technical specifications alone do not determine whether a product will perform well in a project. Buyers also need dependable communication, order coordination, production consistency, packaging support, and after-sales assistance.
Edwin Pump serves customers in international markets and provides procurement and foreign trade services through its related companies. This structure is intended to support purchasing planning, order tracking, cross-border delivery, and project communication. Such support can be useful for buyers managing multiple products, repeat orders, or customized procurement schedules.
The company’s broad portfolio also allows customers to source different pump categories from one supplier. Its product lines include deep well pumps, submersible pumps, domestic booster pumps, circulation pumps, solar pumps, and other water equipment. One-stop procurement can reduce supplier complexity and help buyers coordinate technical requirements across several applications.
For professional purchasers, the XLA403 can be considered not only as an individual pump but also as part of a broader intelligent water equipment strategy. Its permanent magnet drive, compact multistage design, and automatic control functions align with market trends toward energy efficiency, smart operation, and reduced maintenance.
| Item | Specification |
| Model | XLA403 |
| Product type | Self-priming multistage intelligent booster pump |
| Frequency | 50/60 Hz |
| Power range | 100–400 W |
| Maximum flow | 66 L/min |
| Maximum head | 25 m |
| Maximum suction | 5 m |
| Inlet and outlet | 1 inch × 1 inch |
| Maximum speed | 4,800 r/min |
| Net weight | Approximately 4.5 kg |
| Gross weight | Approximately 5.5 kg |
| Dimensions | 301 × 146 × 228 mm |
| Liquid temperature | Above 0°C to 100°C |
| Ambient temperature | 0°C to 40°C |
| Permitted pH range | 4–10 |
| Relative humidity | Maximum 85% RH |
| Protection rating | IP54 |
| Pump body, base, upper cover, impeller | Engineering plastic |
| Shaft seal | Stainless steel |
| Shaft materials | Silicon carbide/graphite |
The pump is designed for clean water and compatible low-viscosity, neutral, non-explosive liquids without fibers. Solid particles should be below 0.1 percent by volume and smaller than 0.2 millimeters. Chemical compatibility must be confirmed before using any liquid other than clean water.
Yes, the specified liquid temperature range is above 0°C to a maximum of 100°C. However, the complete installation, including seals, pipes, valves, fittings, insulation, and safety provisions, must be suitable for the selected temperature.
The maximum rated flow is 66 liters per minute. Actual flow depends on system resistance, pressure setting, suction conditions, pipework, elevation, and operating point.
The maximum head is 25 meters. The pump should be selected using the complete system requirement rather than maximum head alone.
Yes. The intelligent control system is designed to adjust power output according to load and water demand. This supports more efficient operation than a conventional fixed-speed pump that continuously runs at one output level.
The pump incorporates a non-return water structure and sensors that support controlled operation and help prevent reverse flow. Correct pipework and valve design are still necessary for complete water hammer management.
The self-start protection function automatically activates the pump every 12 hours after extended inactivity. This helps reduce the risk of seizing caused by prolonged periods without operation.
The IP54 rating supports use in suitable outdoor or semi-outdoor locations, but the pump must be protected from flooding, immersion, high-pressure water jets, condensation, and conditions outside the specified environmental range.
The XLA403 can support selected light industrial applications, industrial cleaning, water circulation, and water treatment duties. Large systems should be evaluated by a qualified engineer to confirm that the flow, head, liquid characteristics, duty cycle, and connection requirements are appropriate.
Buyers should confirm the required flow, pressure, suction arrangement, liquid temperature, liquid composition, electrical supply, connection size, installation environment, and expected duty cycle. They should also confirm packaging, delivery, technical documentation, and support requirements with the supplier.
The XLA403 Intelligent Permanent Magnet Multistage Pump is designed for users who need more efficient and adaptable water pressure management than a basic fixed-speed pump can provide. Its IE5 permanent magnet motor, efficiency of up to 96 percent, pure copper winding, multistage hydraulic design, one-click pressure regulation, and automatic load response provide a strong combination of performance and convenience.
Its additional functions further improve its practical value. Water hammer reduction supports smoother system operation, self-start protection helps maintain readiness after long periods of inactivity, and IP54 protection supports installation in suitable outdoor or semi-outdoor environments. Engineering plastic hydraulic components help keep the pump compact and lightweight, while the specified shaft and sealing materials support reliable water handling within the intended operating conditions.
The manufacturer’s experience in research and development, mass production, international export, intelligent pump technology, solar pumping, and broad water equipment production provides an important foundation for the product. Its integrated manufacturing structure can support consistent production, coordinated system design, and professional procurement services for international customers.
For residential pressure boosting, water tower systems, hot water circulation, HVAC circulation, water treatment support, industrial cleaning, and other clean-water applications, the XLA403 offers a balanced solution focused on efficiency, intelligent control, compact installation, and dependable operation. Correct sizing, suitable liquid selection, professional installation, and regular maintenance will allow the pump to deliver its intended advantages throughout its service life.
1. Product technical information for the XLA403 Intelligent Permanent Magnet Multistage Pump, including operating conditions, materials, dimensions, and performance data.
2. Manufacturer-provided information regarding intelligent booster pump functions, permanent magnet motor efficiency, self-start protection, pressure regulation, and water hammer reduction.
3. Manufacturer company profile covering research and development, mass production, export services, water pump product lines, and intelligent technology development.
4. General engineering principles for centrifugal pump selection, system head calculation, hydraulic resistance, suction conditions, and pressure boosting.
5. General technical guidance on electric motor efficiency, copper winding construction, permanent magnet motor operation, and variable-load energy management.
6. General water system engineering guidance concerning water hammer, non-return valves, pipe support, filtration, hot water circulation, and pump maintenance.
aseriesnoisereductiondesignacid-baseverticalsurfacepump-1.jpg "EV(F)A Series Noise Reduction Design Acid-base Vertical Surface Pump")
edwina@edwin-pump.com
+86-13586290903 (WhatsApp)
Xuri Gongliang Cutting Tool Entrepreneurship Park, Wenqiao Town, Wenling City, Taizhou City, Zhejiang Province, China
High Performance Smart Pump Factory
English
